Frequency counters
measure the frequency of an input signal. These are commonly used in
laboratories, factories and field environments to provide direct frequency
measurements of various devices.
Most
frequency counters work by using a counter that accumulates the number of
events (oscillations) occurring with in a specific period of time (say, one
second). After the preset time period, the value in the counter is transferred
to a display and the counter is reset to zero.
Circuit description
Fig.1 shows the circuit of a frequency counter built around timer NE555, decade counter/divider CD4033, 7805 regulator, 7-segment display and a few discrete components. Five decade counter- cum-7-segment-driver ICs (each CD4033) are connected in tandem to form a 5-digit decimal counter. IC CD4033 consists of a 5-stage counter and an output decoder that converts the code into a 7-segment decoded output for driving one stage of a numerical display.
Circuit description
Fig.1 shows the circuit of a frequency counter built around timer NE555, decade counter/divider CD4033, 7805 regulator, 7-segment display and a few discrete components. Five decade counter- cum-7-segment-driver ICs (each CD4033) are connected in tandem to form a 5-digit decimal counter. IC CD4033 consists of a 5-stage counter and an output decoder that converts the code into a 7-segment decoded output for driving one stage of a numerical display.
Fig.1: Circuit of frequency counter
The
sinewave signals coming from the oscillator source are first converted into
positive-going pulses with the help of transistor T2 and diode D1. These pulses
are then counted by the 5-digit decimal counter.
If pin 2 of IC3 is at logic ‘0,’ each pulse from the oscillator advances the counter by one. The logic condition of pin 2 is dependent upon the output of the monostable multivibrator built around IC NE555 (IC2).
The NE555 is a highly stable controller capable of producing accurate timing pulses. The time period of the monostable multivibrator is determined by the combination of resistor R5, preset VR1 and capacitor C4. Here it is set precisely to one second.
If pin 2 of IC3 is at logic ‘0,’ each pulse from the oscillator advances the counter by one. The logic condition of pin 2 is dependent upon the output of the monostable multivibrator built around IC NE555 (IC2).
The NE555 is a highly stable controller capable of producing accurate timing pulses. The time period of the monostable multivibrator is determined by the combination of resistor R5, preset VR1 and capacitor C4. Here it is set precisely to one second.
The
monostable multivibrator is triggered by the astable multivibrator built around
another IC NE555 (IC1). The time period of the astable multivibrator is
determined by the combination of resistors R1 and R2 and capacitor C1. Here IC1
is designed to output a square wave having two second ‘high’ and two-second
‘low’ periods.
The monostable multivibrator (IC2) is triggered whenever the output of the astable multivibrator (IC1) goes low. The output of IC2 instantly goes high and remains high for one second. Transistor T1 inverts the output of IC2 to make input pin 2 of IC3 low.
As
soon as IC2 is triggered, the leading edge of the positive-going output pulse
sends resting signal to all the decade counters via capacitor C6. The five
7-segment displays (DIS1 through DIS5) now show the count as ‘00000.’ As pin 2
of IC3 is low, the counter is enabled to count for one second. It continues
counting the input pulses as long as the output of IC2 remains high.
After one second, the output of IC2 becomes low again. Transistor T1 is cut-off, prohibiting further counting by pulling up pin 2 of IC3 to logic ‘1.’ The number of pulses counted so far is displayed over 7-segment displays.
The process repeats, as long as power is applied to the counter circuit. Pin 5 of timer NE555 is the control voltage pin that is primarily used for filtering when the timer is used in noisy environments. However, by imposing a voltage at this pin, it is possible to vary the calculated period. A 0.01μF capacitor connected to pin 5 of NE555 bypasses any noise from altering the calculated pulse-width. LED2 indicates the counting period.
Fig.
2 shows the power supply circuit. The 230V, 50Hz AC mains is stepped down by
transformer X1 to deliver a secondary output of 9V, 500mA. The transformer
output is rectified by full-wave rectifier BR1, filtered by capacitor C7 and
regulated by IC 7805 (IC8). The regulated 5V DC so obtained is further filtered
by capacitors C8 and C9. LED3 acts as the power indicator. Resistor R14 acts as
the current limiter. A capacitor above 10 μF is connected across the output of
the regulator IC, while diode D1 protects the regulator IC in case its input is
shorted to ground.
Fig.2: Power supply circuit
Construction
Carefully assemble the components and double-check for any overlooked error. Use a low-capacitance cable to feed signal from the oscillator source to the frequency counter. Connect a known-frequency source (like calibration signal of an oscilloscope) to the input of the counter and adjust trimpot VR1 to display the frequency on the 7- segment displays.
Source: Electronics For You Magazine
No comments:
Post a Comment